You should post this to the original thread. It is good manners to respond
to someone who tried to help you. There are other questions that need to be
asked to continue trouble shooting but it would be best to keep to the
original thread so that people searching for similar problems will see the
full thread. The way it is now no one can follow through all the trouble
shooting steps.
--
Kerry Brown
MS-MVP - Windows Desktop Experience: Systems Administration
http://www.vistahelp.ca/phpBB2/
"Paavo Leinonen" <PaavoLeinonen@xxxxxx> wrote in message
news:A4855C84-62FB-46C5-8582-CA6AF73A1591@xxxxxx
| Quote: |  | |
|
> Hi,
>
> I did, I was going to update this after a few more tests but here is the
> current situation.
>
> MaxMpxCt is now 100 (default 10), MaxWorkItems is now 512 (default 64),
> and
> the Size is now 2 (default was 1). These are located in
> HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Lanmanserver\Parameters.
> Adjusting there parameters did not change the Vista server behaviour at
> all.
>
> I also tried adjusting NonPagedPoolSize to 40000000hex (default was 0) in
> HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory
> Management, but this did not help either.
>
> The other links were also good but did not help me to solve this problem.
>
> Anything else I can try? This feels a litttle bit stupid, quad-core 4GB
> computer with 64-bit Vista Ultimate cannot serve single XP client doing
> heavy
> disk operations over 100mbits local area connection. And this is about the
> only problem there is, all the computers and the home network is operating
> very nicely.
>
> But the problem is very easy to repeat: reboot the server, start copying
> 10000+ little pictures (filesize ~10-200kB, resolution less than 1k*1k
> pixels) from the XP client disk to the Vista server disk, and in a minute
> or
> so the server dies to the XP client, all commands fail (dir z:, net use,
> net
> view, etc.). But the Vista server continues to server another (Vista
> 64-bit)
> client.
>
> SHould I adjust Lanmanserver/Parameters Size to 3? The Vista server was
> not
> used otherwise, then the XP client used the disk, to there was no other
> load
> for it.
>
> -Paavo
>
> "Kerry Brown" wrote:
> | Quote: | | | |
>> Did you check out the links Meinolf Weber posted to your thread in
>> another
>> newsgroup?
>>
>> --
>> Kerry Brown
>> MS-MVP - Windows Desktop Experience: Systems Administration
>> http://www.vistahelp.ca/phpBB2/
>>
>>
>>
>> "Paavo Leinonen" <PaavoLeinonen@xxxxxx> wrote in
>> message
>> news:92FA5054-9664-4EF7-A165-5089B75A886C@xxxxxx | Quote: | | | |
>> > Hi,
>> >
>> > I have Vista Ultimate 64-bit computer as a server for home network. The
>> > clients are mixed Vista (Ultimate) 64-bit and XP (Professional) 32-bit
>> > computers.
>> >
>> > After installing Vista SP1 the Vista server reliability has gone bad
>> > for
>> > XP
>> > clients.
>> >
>> > When I use one of the Vista server disk shares from XP client heavily,
>> > the
>> > connection does down and I get "Not enough server storage is available
>> > to
>> > process this command" and/or "System error 58" in the client side.
>> >
>> > Vista server event viewer shows these error messages soon after the
>> > problems:
>> >
>> > - The server was unable to allocate from the system nonpaged pool
>> > because
>> > the pool was empty (system log / source srv / event ID 2019)
>> >
>> > - The server was unable to allocate from the system nonpaged pool
>> > because
>> > the server reached the configured limit for nonpaged pool allocations
>> > (system
>> > log / source srv / event ID 2017)
>> >
>> > - The server was unable to allocate a work item 43419 times in the last
>> > 60
>> > seconds (system log / source srv / event ID 2021) - this is a warning
>> > only
>> >
>> > The funny thing is that I can continue to use the same disk share from
>> > Vista
>> > client, but to be able to use the server again from the XP client I
>> > need
>> > to
>> > reboot the Vista server (no actions needed in the XP client side).
>> >
>> > In the performance monitor looks like nonpaged pool is sixty something
>> > megabytes, and only like 10% allocated. However, I have not done any
>> > tunings
>> > or adjustments to the server or client systems, I think the swap file
>> > set-up
>> > is about the only relevant thing, and all computers ave "enough"
>> > permanent
>> > swap (several gigabytes for the XP computers, something like 12-16
>> > gigabytes
>> > for the Vista server and client).
>> >
>> > XP clients have 2GB of RAM, Vista computers have 4GB (both client and
>> > server).
>> >
>> > Local IP addresses in use, 192.168.xxx.yyy. Switched 100/1000 mbits
>> > network.
>> >
>> > How can I fix this?
>> >
>> > -Paavo
>> >
| | | | | >> | | | | | | |
| | |