1: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high. This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: fffffa60010f3064, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000008, value 0 = read operation, 1 = write operation
Arg4: fffffa60010f3064, address which referenced memory
Debugging Details:
------------------

READ_ADDRESS: fffffa60010f3064
CURRENT_IRQL: 2
FAULTING_IP:
Ntfs!NtfsCopyReadA+390
fffffa60`010f3064 53 push rbx
CUSTOMER_CRASH_COUNT: 10
DEFAULT_BUCKET_ID: COMMON_SYSTEM_FAULT
BUGCHECK_STR: 0xD1
PROCESS_NAME: svchost.exe
TRAP_FRAME: fffffa6008f477e0 -- (.trap 0xfffffa6008f477e0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=fffffa60010f3064 rbx=0000000000000000 rcx=fffffa6008f479b0
rdx=fffffa6008f48790 rsi=0000000000000000 rdi=0000000000000000
rip=fffffa60010f3064 rsp=fffffa6008f47978 rbp=fffffa6008f47ab0
r8=fffffa6008f481d0 r9=fffffa6008f47ab0 r10=fffffa6008f48130
r11=fffffa6008f479e8 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei ng nz na pe nc
Ntfs!NtfsCopyReadA+0x390:
fffffa60`010f3064 53 push rbx
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff800020a40ee to fffff800020a4350
FAILED_INSTRUCTION_ADDRESS:
Ntfs!NtfsCopyReadA+390
fffffa60`010f3064 53 push rbx
STACK_TEXT:
fffffa60`08f47698 fffff800`020a40ee : 00000000`0000000a fffffa60`010f3064 00000000`00000002 00000000`00000008 : nt!KeBugCheckEx
fffffa60`08f476a0 fffff800`020a2fcb : 00000000`00000008 fffffa60`08f48790 00000000`00000000 fffffa60`01054784 : nt!KiBugCheckDispatch+0x6e
fffffa60`08f477e0 fffffa60`010f3064 : fffff800`020b77d8 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x20b
fffffa60`08f47978 fffff800`020b77d8 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : Ntfs!NtfsCopyReadA+0x390
fffffa60`08f47980 fffff800`020b76bd : fffffa60`08f48790 fffffa60`08f48790 fffffa60`08f48130 fffffa60`010c1136 : nt!_C_specific_handler+0x8c
fffffa60`08f479f0 fffff800`020becff : fffffa60`00000001 00000000`00000000 00000000`00000000 fffffa60`08f48790 : nt!RtlpExecuteHandlerForException+0xd
fffffa60`08f47a20 fffff800`020bcb7e : fffffa60`08f48130 fffffa60`08f481d0 fffffa80`00000001 fffff6fc`c0014b00 : nt!RtlDispatchException+0x22f
fffffa60`08f48110 fffff800`02317144 : 00000000`00000000 fffffa80`0a524160 00000000`00000002 00000000`01081000 : nt!RtlRaiseStatus+0x4e
fffffa60`08f486b0 fffffa60`010c1136 : fffffa80`0a5209d0 00000000`00000000 00000000`00010000 00000000`01091000 : nt!CcFastCopyRead+0x2e4
fffffa60`08f48790 fffffa60`00a07248 : 00000000`00000010 fffffa60`08f487f0 00000000`00010000 fffffa80`0a520a01 : Ntfs!NtfsCopyReadA+0x1e6
fffffa60`08f48980 fffffa60`00a0a1d5 : fffffa60`08f48a60 00000000`00000000 fffffa80`0a520903 fffffa80`00000000 : fltmgr!FltpPerformFastIoCall+0x88
fffffa60`08f489e0 fffffa60`00a24599 : 00000000`00000000 00000000`00446640 00000000`00000000 00000000`00000000 : fltmgr!FltpPassThroughFastIo+0xb5
fffffa60`08f48a30 fffff800`0230dfba : fffffa80`0a5209d0 fffff800`00000001 fffffa80`066fd080 fffffa80`0a5209d0 : fltmgr!FltpFastIoRead+0x1a9
fffffa60`08f48ad0 fffff800`020a3df3 : 00000000`00000228 00000000`00000000 00000000`00000000 00000000`00000000 : nt!NtReadFile+0x3f8
fffffa60`08f48bb0 00000000`77175ada : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
00000000`000fe9c8 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x77175ada

STACK_COMMAND: kb
FOLLOWUP_IP:
Ntfs!NtfsCopyReadA+390
fffffa60`010f3064 53 push rbx
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: Ntfs!NtfsCopyReadA+390
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: Ntfs
IMAGE_NAME: Ntfs.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 479190d1
FAILURE_BUCKET_ID: X64_0xD1_CODE_AV_BAD_IP_Ntfs!NtfsCopyReadA+390
BUCKET_ID: X64_0xD1_CODE_AV_BAD_IP_Ntfs!NtfsCopyReadA+390
Followup: MachineOwner

1E

2: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

KMODE_EXCEPTION_NOT_HANDLED (1e)
This is a very common bugcheck. Usually the exception address pinpoints
the driver/function that caused the problem. Always note this address
as well as the link date of the driver/image that contains this address.
Arguments:
Arg1: ffffffffc0000005, The exception code that was not handled
Arg2: fffff800020dcdf2, The address that the exception occurred at
Arg3: 0000000000000000, Parameter 0 of the exception
Arg4: ffffffffffffffff, Parameter 1 of the exception

Debugging Details:
------------------


EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

FAULTING_IP:
nt!MiUnlinkFreeOrZeroedPage+112
fffff800`020dcdf2 4c095028 or qword ptr [rax+28h],r10

EXCEPTION_PARAMETER1: 0000000000000000

EXCEPTION_PARAMETER2: ffffffffffffffff

READ_ADDRESS: GetPointerFromAddress: unable to read from fffff8000228e080
ffffffffffffffff

CUSTOMER_CRASH_COUNT: 3

DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

BUGCHECK_STR: 0x1E

PROCESS_NAME: dwm.exe

CURRENT_IRQL: 2

LAST_CONTROL_TRANSFER: from fffff80002093e47 to fffff800020ba350

STACK_TEXT:
fffffa60`0935e128 fffff800`02093e47 : 00000000`0000001e ffffffff`c0000005 fffff800`020dcdf2 00000000`00000000 : nt!KeBugCheckEx
fffffa60`0935e130 fffff800`020ba1a9 : fffffa60`0935e868 fffffa80`01031400 fffffa60`0935e910 00000000`000565c0 : nt! ?? ::FNODOBFM::`string'+0x29317
fffffa60`0935e730 fffff800`020b8d8d : 00000000`0723aa00 00000000`00000000 00000000`00000000 fffff700`01080000 : nt!KiExceptionDispatch+0xa9
fffffa60`0935e910 fffff800`020dcdf2 : fffffa80`0a23c928 fffff700`01080000 fffffa60`0935eba0 fffff800`020edf4e : nt!KiGeneralProtectionFault+0xcd
fffffa60`0935eaa0 fffff800`020dcaca : 00000000`00000000 00000000`00000000 00000000`00000000 fffff700`01080000 : nt!MiUnlinkFreeOrZeroedPage+0x112
fffffa60`0935eae0 fffff800`020ca4cb : fffffa80`0a247060 00000000`00000000 fffff680`00043938 fffffa80`0a247060 : nt!MiRemoveAnyPage+0xda
fffffa60`0935eb30 fffff800`020b8ed9 : 00000000`00000001 fffffa60`0935eca0 fffffa60`0935ea01 00000000`00000000 : nt!MmAccessFault+0x24db
fffffa60`0935ec20 000007fe`fe1713da : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x119
00000000`0311d368 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x7fe`fe1713da


STACK_COMMAND: kb

FOLLOWUP_IP:
nt!MiUnlinkFreeOrZeroedPage+112
fffff800`020dcdf2 4c095028 or qword ptr [rax+28h],r10

SYMBOL_STACK_INDEX: 4

SYMBOL_NAME: nt!MiUnlinkFreeOrZeroedPage+112

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: nt

DEBUG_FLR_IMAGE_TIMESTAMP: 48d1ba35

IMAGE_NAME: memory_corruption

FAILURE_BUCKET_ID: X64_0x1E_nt!MiUnlinkFreeOrZeroedPage+112

BUCKET_ID: X64_0x1E_nt!MiUnlinkFreeOrZeroedPage+112

Followup: MachineOwner
---------

PAGE_FAULT_IN_NONPAGED_AREA (50)

1: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced. This cannot be protected by try-except,
it must be protected by a Probe. Typically the address is just plain bad or it
is pointing at freed memory.
Arguments:
Arg1: fffff800221c591c, memory referenced.
Arg2: 0000000000000000, value 0 = read operation, 1 = write operation.
Arg3: fffff80002319c81, If non-zero, the instruction address which referenced the bad memory
address.
Arg4: 0000000000000002, (reserved)
Debugging Details:
------------------

Could not read faulting driver name
READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80002278080
fffff800221c591c
FAULTING_IP:
nt!NtQuerySystemInformation+441
fffff800`02319c81 8b819c220000 mov eax,dword ptr [rcx+229Ch]
MM_INTERNAL_CODE: 2
CUSTOMER_CRASH_COUNT: 6
DEFAULT_BUCKET_ID: COMMON_SYSTEM_FAULT
BUGCHECK_STR: 0x50
PROCESS_NAME: OIS.EXE
CURRENT_IRQL: 0
TRAP_FRAME: fffffa600b6817d0 -- (.trap 0xfffffa600b6817d0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0000000000000000 rbx=0000000000000001 rcx=fffff800021c3680
rdx=fffff80002278640 rsi=0000000075813380 rdi=fffff800023397a7
rip=fffff80002319c81 rsp=fffffa600b681960 rbp=fffffa600b681ca0
r8=0000000000000000 r9=000000000079ee63 r10=0000000000001a16
r11=00000000000c6bb6 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei pl zr na po nc
nt!NtQuerySystemInformation+0x441:
fffff800`02319c81 8b819c220000 mov eax,dword ptr [rcx+229Ch] ds:4c10:fffff800`021c591c=????????
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff800020b2524 to fffff800020a4350
STACK_TEXT:
fffffa60`0b6816d8 fffff800`020b2524 : 00000000`00000050 fffff800`221c591c 00000000`00000000 fffffa60`0b6817d0 : nt!KeBugCheckEx
fffffa60`0b6816e0 fffff800`020a2ed9 : 00000000`00000000 fffffa60`0b681940 fffffa60`0b681800 00000000`00000000 : nt!MmAccessFault+0x534
fffffa60`0b6817d0 fffff800`02319c81 : 00000000`00000001 00000000`00000001 00000000`00000001 fffffa60`0b681c01 : nt!KiPageFault+0x119
fffffa60`0b681960 fffff800`020a3df3 : fffffa80`08197720 00000000`00000000 00000000`0007e558 00000000`0007e578 : nt!NtQuerySystemInformation+0x441
fffffa60`0b681c20 00000000`776b5dda : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
00000000`0007e4e8 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x776b5dda

STACK_COMMAND: kb
FOLLOWUP_IP:
nt!NtQuerySystemInformation+441
fffff800`02319c81 8b819c220000 mov eax,dword ptr [rcx+229Ch]
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: nt!NtQuerySystemInformation+441
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 48d1ba35
FAILURE_BUCKET_ID: X64_0x50_nt!NtQuerySystemInformation+441
BUCKET_ID: X64_0x50_nt!NtQuerySystemInformation+441
Followup: MachineOwner

anyone?

On Thu, 8 Jan 2009 16:53:44 -0600, Mark77 <guest@xxxxxx-email.com>
wrote:

>anyone?

No one.

Originally Posted by Randall Flagg

On Thu, 8 Jan 2009 16:53:44 -0600, Mark77 <guest@xxxxxx-email.com>
wrote:

>anyone?

No one.

damn, I thought there would be someone with an idea

I got simliar BSOD's:
STOP 7E
STOP 1E
STOP 51

Like today , I was booting into vista x64 Ultimate and leaving the computer. When I came back, There was a STOP 7E Bluescreen.

I have this crash only when the computer is cold. So after rebooting it does not crash again. Since I exchanged all hardware, I do not know what to send back.
Is it probably the CPU (Intel Quad Q6600 G0), the Mainboard P5Q-Pro or the video card (GTX 260 v2)??
Did you find the cause?

Stop 7E

See the last 2 lines in my post below

0x0000007E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
(Click to consult the online MSDN article.)
A system thread generated an exception which the error handler did not catch. There
are numerous individual causes for this problem, including hardware incompatibility,
a faulty device driver or system service, or some software issues. Check Event
Viewer (EventVwr.msc) for additional information.
a.. “0x0000007E, 0xC0000005, 0xFC5CCAF3, 0xFC90F8C0, 0xFC90F5C0” Error Message at
Startup {KB 321637} Win XP
b.. 0x0000007e Error When Registering OLEMSG32.DLL or CDO.DLL Files {KB 238265}
Win NT, Win 2000
c.. 0x7E Error Occurs in Kbdclass.sys When You Try to Shut Down Win XP {KB 313050}
Win XP Professional
d.. Error message in Win XP Service Pack 2: “Stop 0x7E” {KB 900485} Win XP SP2
(Timing issue — patch available)
e.. Stop error 0x7E in PCI.SYS {KB 839641} Win 2000, Win XP, Server 2003
f.. Stop Error 0x7E in USBHUB.SYS {KB 327863} Win 2000, Win XP, Server 2003 (If
USB bandwidth consumption exceeds 100%)
g.. “STOP 0x0000007E” Error Message After You Upgrade to Windows XP {KB 330182}
Win XP
h.. “Stop 0x0000007E” error message when installing Win XP Disk Image from a
Remote Installation Services Server {KB 818966} Win XP
i.. “Stop 0x0000007E” error message after you upgrade to Win XP Service Pack 2 on
a non-Intel-processor computer {KB 888372} Win XP SP2
j.. After installing Win XP SP2 or Win XP Tablet PC Edition 2005, your computer
restarts continuously {KB 873161} Win XP SP2, Win XP Tablet 2005 (UMAX scanner
issue)
k.. Problems after you resume Windows Vista from sleep or hibernation {KB 929734}
Vista (various device hangs etc. — hotfix available — see also KB 925528)
l.. Occasional Error Message on Portable Vista-based Computer That Wakes From
Sleep to Perform Network-related Tasks: STOP 0x0000007E {KB 930311} Vista (hotfix
available)

--
Peter

Please Reply to Newsgroup for the benefit of others
Requests for assistance by email can not and will not be acknowledged.

"PSputnik" <guest@xxxxxx-email.com> wrote in message
news:22bf3757b4407471963b1021584c3abb@xxxxxx-gateway.com...

>
> I got simliar BSOD's:
> STOP 7E
> STOP 1E
> STOP 51
>
> Like today , I was booting into vista x64 Ultimate and leaving the
> computer. When I came back, There was a STOP 7E Bluescreen.
>
> I have this crash only when the computer is cold. So after rebooting it
> does not crash again. Since I exchanged all hardware, I do not know what
> to send back.
> Is it probably the CPU (Intel Quad Q6600 G0), the Mainboard P5Q-Pro or
> the video card (GTX 260 v2)??
> Did you find the cause?
>
>
> --
> PSputnik