Vista - Install missing driver Beta 2 (x86)

I am trying to install the beta from a DVD of the Beta, I get to a window
that says "Select the driver to be installed". When I select ok, I get a
dialog titled "LOAD DRIVER". This message says "No device drivers were found.
Make sure that the installation media contains the correct drivers, and then
click OK." The only option is an OK button, and I am stuck in a loop.
clicking the OK button.

Is there any way that you can avoid this? Or does it just popup
automatically?
If it does... then if you have the ISO still (presuming you've downloaded it
and not received the physical media), then try out 3 here >
http://www.vistabase.co.uk/welcome.php?getstarted

A lot of people who have troubles during install can be solved on that page
)

--
Zack Whittaker
» ZackNET Enterprises: www.zacknet.co.uk
» MSBlog on ResDev: www.msblog.org
» Vista Knowledge Base: www.vistabase.co.uk
» This mailing is provided "as is" with no warranties, and confers no
rights. All opinions expressed are those of myself unless stated so, and not
of my employer, best friend, Ghandi, my mother or my cat. Glad we cleared
that up!

--: Original message follows :--
"JSass" <JSass@discussions.microsoft.com> wrote in message
news:05DA2680-C847-4025-A719-8E96733A8D1E@microsoft.com...
>I am trying to install the beta from a DVD of the Beta, I get to a window
> that says "Select the driver to be installed". When I select ok, I get a
> dialog titled "LOAD DRIVER". This message says "No device drivers were
> found.
> Make sure that the installation media contains the correct drivers, and
> then
> click OK." The only option is an OK button, and I am stuck in a loop.
> clicking the OK button.
>
>

Press Shift + F10 to open a command prompt
Start the disk partition utility: diskpart
Enter the following command to partition the hard disk:
select disk 0
create partition primary

When the partition process is complete, click Reset button to reboot the
computer.
Boot back again from the Vista DVD

In certain Vista builds, the installer chooses an incorrect default in the
screen titled "Choose your installation destination. It shows a partition
with 0 MB free and makes that partition the default destination.

At that screen, you must change the choice to the disk (instead of the
partition), then click Continue.
--
--
Andre
Windows Connected | http://www.windowsconnected.com
Extended64 | http://www.extended64.com
Blog | http://www.extended64.com/blogs/andre
http://spaces.msn.com/members/adacosta

"JSass" <JSass@discussions.microsoft.com> wrote in message
news:05DA2680-C847-4025-A719-8E96733A8D1E@microsoft.com...
>I am trying to install the beta from a DVD of the Beta, I get to a window
> that says "Select the driver to be installed". When I select ok, I get a
> dialog titled "LOAD DRIVER". This message says "No device drivers were
> found.
> Make sure that the installation media contains the correct drivers, and
> then
> click OK." The only option is an OK button, and I am stuck in a loop.
> clicking the OK button.
>
>

The solution that have been suggested didnt help me and I have the same
problem.
Any more ideas?
--
/Z


"JSass" wrote:

> I am trying to install the beta from a DVD of the Beta, I get to a window
> that says "Select the driver to be installed". When I select ok, I get a
> dialog titled "LOAD DRIVER". This message says "No device drivers were found.
> Make sure that the installation media contains the correct drivers, and then
> click OK." The only option is an OK button, and I am stuck in a loop.
> clicking the OK button.
>
>

The solution that have been suggested didnt help me and I have the same
problem.
Any more ideas?
--
/Z


"JSass" wrote:

> I am trying to install the beta from a DVD of the Beta, I get to a window
> that says "Select the driver to be installed". When I select ok, I get a
> dialog titled "LOAD DRIVER". This message says "No device drivers were found.
> Make sure that the installation media contains the correct drivers, and then
> click OK." The only option is an OK button, and I am stuck in a loop.
> clicking the OK button.
>
>