|
 |  |  |  |  |  |  |
| Welcome to Windows Vista Forums. Our forum is dedicated to helping you find solutions with any problems, errors or issues you are experiencing with Windows Vista. The Vista forum also covers news and updates and has an extensive Windows Vista tutorial section that covers a wide range of tips and tricks. |
| |||||||
 |
| |
08-10-2008
| #1 (permalink) |
| | DCOM Error 10009 Hi All I have a home network consisting of a laptop (Vista Premium+SP1) and desktop (XP Home+ SP2 with a shared printer attached). Recently, my laptop started generating log messages 2 / minute of the type: "DCOM was unable to communicate with the computer Desktop using any of the configured protocols" - with Event id 10009. Most of the research I've done suggests it might occur if there is an invalid printer, computer or other device on the network. This doesn't seem to be the case here. Other suggestions point to: a) firewall exception COM+ Network Access not Enabled. - in my case I don't even have such a rule. b) Review RPC error messages. I looked at these and they are: 311 - wsopen20 - RPC failed to bind or connect to server 312 - wsopen30 - RPC could not open socket 318 - wsopen90 - RPC called connecter but failed. Error in originating NTStatus error code 1442 - ??? (can't find info on this but the error points to the XP computer <Desktop>) 1710 - ??? (can't find info on this) c) Ensure the req'd properties for remote access are configured. These seem to be in order. I have "connection-oriented" followed by "Tunneling TCP/IP" protocols listed I can communicated between the 2 CPU ok and use the shared printer. Anyone know why this suddenly started and how to fix this error? TIA |
My System Specs |
|
08-11-2008
| #2 (permalink) |
| | Re: DCOM Error 10009 In most cases, this is firewall issue. This post may help. Event ID 10009 DCOM was unable to communicate with computer http://www.chicagotech.net/netforums...hp?p=7596#7596 -- Bob Lin, MS-MVP, MCSE & CNE Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net How to Setup Windows, Network, VPN & Remote Access on http://www.HowToNetworking.com "garyf" <news@xxxxxx> wrote in message news:e1IQDax%23IHA.872@xxxxxx Quote: > Hi All > > I have a home network consisting of a laptop (Vista Premium+SP1) and > desktop (XP Home+ SP2 with a shared printer attached). Recently, my laptop > started generating log messages 2 / minute of the type: > > "DCOM was unable to communicate with the computer Desktop using any of > the configured protocols" - with Event id 10009. > > > Most of the research I've done suggests it might occur if there is an > invalid printer, computer or other device on the network. This doesn't > seem to be the case here. Other suggestions point to: > a) firewall exception COM+ Network Access not Enabled. - in my case I > don't even have such a rule. > b) Review RPC error messages. I looked at these and they are: > 311 - wsopen20 - RPC failed to bind or connect to server > 312 - wsopen30 - RPC could not open socket > 318 - wsopen90 - RPC called connecter but failed. Error in originating > NTStatus error code > 1442 - ??? (can't find info on this but the error points to the XP > computer <Desktop>) > 1710 - ??? (can't find info on this) > c) Ensure the req'd properties for remote access are configured. These > seem to be in order. I have "connection-oriented" followed by "Tunneling > TCP/IP" protocols listed > > I can communicated between the 2 CPU ok and use the shared printer. Anyone > know why this suddenly started and how to fix this error? > > TIA > > > > |
| My System Specs |
|
08-13-2008
| #3 (permalink) |
| | Re: DCOM Error 10009 Thank you for your response ... will investigate and respond to group on results "Robert L. (MS-MVP)" <findemail@xxxxxx> wrote in message news:uWPTeM##IHA.3392@xxxxxx Quote: > In most cases, this is firewall issue. This post may help. > > Event ID 10009 DCOM was unable to communicate with computer > http://www.chicagotech.net/netforums...hp?p=7596#7596 > > -- > Bob Lin, MS-MVP, MCSE & CNE > Networking, Internet, Routing, VPN Troubleshooting on > http://www.ChicagoTech.net > How to Setup Windows, Network, VPN & Remote Access on > http://www.HowToNetworking.com > "garyf" <news@xxxxxx> wrote in message > news:e1IQDax%23IHA.872@xxxxxx Quote: >> Hi All >> >> I have a home network consisting of a laptop (Vista Premium+SP1) and >> desktop (XP Home+ SP2 with a shared printer attached). Recently, my >> laptop started generating log messages 2 / minute of the type: >> >> "DCOM was unable to communicate with the computer Desktop using any of >> the configured protocols" - with Event id 10009. >> >> >> Most of the research I've done suggests it might occur if there is an >> invalid printer, computer or other device on the network. This doesn't >> seem to be the case here. Other suggestions point to: >> a) firewall exception COM+ Network Access not Enabled. - in my case I >> don't even have such a rule. >> b) Review RPC error messages. I looked at these and they are: >> 311 - wsopen20 - RPC failed to bind or connect to server >> 312 - wsopen30 - RPC could not open socket >> 318 - wsopen90 - RPC called connecter but failed. Error in >> originating NTStatus error code >> 1442 - ??? (can't find info on this but the error points to the XP >> computer <Desktop>) >> 1710 - ??? (can't find info on this) >> c) Ensure the req'd properties for remote access are configured. These >> seem to be in order. I have "connection-oriented" followed by "Tunneling >> TCP/IP" protocols listed >> >> I can communicated between the 2 CPU ok and use the shared printer. >> Anyone know why this suddenly started and how to fix this error? >> >> TIA >> >> >> >> |
| My System Specs |
|
| Thread Tools | |
| |
Similar Threads | ||||
| Thread | Forum | |||
| Dcom ends with error | Vista performance & maintenance | |||
| dcom error | Vista performance & maintenance | |||
| DCOM Thumbnail.dll permissions | Vista security | |||
| DCOM server error on vista home premium | Vista security | |||
| DCOM with Vista | Vista security | |||
