And a very Good Morning to you all at 2:24am from Sydney, Australia!!!
I draw your attention to the image attached below which I have extracted from Lavalys Everest Ultimate Edition's Memory Benchmarking Test.
As I only confess to having no more than an intermediate computer knowledge, could someone please answer my following query:
Why in the image does it display my Memory Type as being Dual Channel DDR2-667 SDRAM (5-5-5-12) when what I have installed is Dual Channel DDR2-800 RAM (4-4-4-12)?
Any information and assistance would be much appreciated.
Do you have any DDR2 667 MHz RAM sticks installed with the 800 MHz ones? If you do, the 800 MHz will step down to 667 MHz automatically. You should also double check your motherboard memory jumpers and BIOS settings to make sure that they are correct.
When I added the extra 2GB of G-Skill RAM recently, I made sure that they were identical to the existing 2GB being: G-Skill F2 6400 PHU2 2GB HZ DDRII 1GB PC2 6400 444/12)
Can you take a look at the attachments below from CPU-Z when you get a chance (no rush please ... you have larger fish to fry I'm sure) and let me know if all appears to be okay.
CPU-Z is showing that you are using 800 MHz RAM, but it looks like the RAM in slots 2 and 4 are using EPP set at the 667 MHz setting instead of it's 800 MHz rating. I would look at the BIOS settings for them to adjust them to their 800 MHz settings (JEDEC#2) in CPU-Z.
I was just saying to 'Sharp' who also sent me some valuable advice on this matter and whose instructions I just followed ie:
I went into Setup and under 'Jumpfree Configuration' chose Manual and selected 800MHz for DRAM Frequency and Memory Voltage to 2.0.
Result? Unable to Boot. Screen read 'Overclocking or Over Voltage Failed'
I uninstalled the Asus Software called Ai Booster which only gave me the option to increase it to 711MHz.
Current Status: Everything in the Jumpfree Configuration settings is on Auto other than the DRAM Frequency which I've been able to increase to 711MHz and the CPU Frequency which says 266 and in a window next to this it says Valid Input Value 100 - 550.
I'm sure that will all make alot more sense to you and Sharp than it does to me.
The first one booted up with a CPU speed of 2.16MHz, the second one booted up with a CPU speed of 2.70GHz, and the third option did not allow me to boot up at all.
Therefore, I have selected the second option and I hope this is what I was meant to do in order to have my 4 RAM sticks correctly setup.
(ignore the memory voltage in this screenshot)
[media]http://img.hexus.net/v2/motherboards/intel/asus/P5WDH/P5W-DH_Deluxe_BIOS_jumper_free-big.jpg[/media]
And at this section set the SPD option to enable
[media]http://img.hexus.net/v2/motherboards/intel/asus/P5WDH/P5W-DH_Deluxe_BIOS_chipset1-big.jpg[/media]
I would suggest Mr Smiley to swap the sticks around. I would also urge you to carefully go through your printed motherboard manual. There are specific positions required for RAM sticks.Make sure you have followed them.
The screenshots shown by sharp are very much similar to what i find in my bios setup and if Mr Smiley looks at the first of them, he'll find his answer right there.
I think I've figured it out now, but I would appreciate it if you could review my CPU-Z & Everest attachments when convenient for confirmation that my RAM configuration is now correct.
I went into Jumpfree Configuration and Disabled DRAM Frequency which allowed me to change the numbers from 5-4-4 /15 I think it was from memory (no pun intended) to 4-4-4 / 12 and it then allowed me to change the DRAM Frequency to DDR2 800 without having to go into Overclocking Options as I had done earlier.
I look forward to receiving your valued feedback at your convenience.
It looks good to me. It does look like you have a slightly different type of memory in slots 2 and 4, but they are compatible with the others in slot 1 and 3.
Hey Sharp, thanks for the image tip, but I was also wondering how I can display images like you did on the first page of this post ... the setup screenshots where you click to enlarge.
